Cisco Ccna / Ccnp Certification Exam Tutorial: Eigrp And Split Horizon

R1#show ip route eigrp

2.0.0.0/32 is subnetted, 1 subnets

D 2.2.2.2 [90/2297856] via 172.12.123.2, 00:03:29, Serial0

3.0.0.0/32 is subnetted, 1 subnets

D 3.3.3.3 [90/2297856] via 172.12.123.3, 00:03:29, Serial0

R2#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/2297856] via 172.12.123.1, 00:05:20, Serial0

R3#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/2297856] via 172.12.123.1, 00:07:54, Serial0

EIGRP runs split horizon by default, making it impossible for R1 to forward an advertisement to R2 regarding R3’s loopback. Likewise, R1 cannot advertise R2’s loopback address to R3. We could configure two subinterfaces on R1 to resolve this issue, but here we’re going to disable split horizon instead.

R1(config)#int serial0

R1(config-if)#no ip split-horizon ?

eigrp Enhanced Interior Gateway Routing Protocol (EIGRP)

R1(config-if)#no ip split-horizon eigrp ?

<1-65535> Autonomous system number

R1(config-if)#no ip split-horizon eigrp 100

04:10:02: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0) is down: split horizon changed

04:10:02: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0) is down: split horizon changed

04:10:25: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0) is up: new adjacency

04:10:37: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0) is up: new adjacency

Note that disabling split horizon resulted in the EIGRP adjacencies being torn down. They came back up 20 – 35 seconds after being torn down according to the timestamps, but that’s a good detail to keep in mind!

The routing tables of each spoke should now show the loopback network configured on the remote spoke.

R2#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/2297856] via 172.12.123.1, 00:00:02, Serial0

3.0.0.0/32 is subnetted, 1 subnets

D 3.3.3.3 [90/2809856] via 172.12.123.1, 00:00:02, Serial0

R3#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/2297856] via 172.12.123.1, 00:00:02, Serial0

2.0.0.0/32 is subnetted, 1 subnets

D 2.2.2.2 [90/2809856] via 172.12.123.1, 00:00:02, Serial0

Be careful when disabling split horizon. In this scenario, R1 can and will advertise routes out Serial0 that were learned about on that interface in the first place, and that’s not always desirable. Split horizon is enabled by default for a reason, so be careful when disabling it!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNP and CCNA tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website. For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, just visit the website! You can also get FREE CCNA and CCNP exam questions every day! Get your Microsoft Vista certification with The Bryant Advantage!

Article Source: http://www.thearticleinsiders.com